33.5 in. Silverwing Double-Sided Retractable Banner Stand – 80″H Fabric Graphic Package

Construction:
The Silverwing is finished in anodized aluminum and heavy duty plastic end plates. It is quick and simple to use and holds 33.5″w x 69″ to 92″H banners (with a 6″ bottom bleed).

Set up: Banner attaches by tape on the bottom and by Clamp bar on the top.

Graphic Material: Fabric

Base Size: 35″W x 3″H x 8.5″D

Includes:

• (2) Single-Sided 33.5″w x 80″h Graphic Print
• Double-Sided Retractable Base
• Top cross bar
• Adjustable support pole
• Silverwing travel bag (11.5″ x 40″ x 4″)

Who Gets the Most Value From This Configuration

This stand earns its place in a few specific situations where a single-sided unit would leave visibility on the table.

The most common buyer is an exhibitor working a standard 10×10 or 10×20 trade show booth who wants to catch foot traffic from two directions without committing to two separate stands and two separate bags to carry. Placing the 33.5 x 80 fabric double sided retractable banner stand at the open corner of a booth means attendees walking the main aisle and the cross-aisle both see branded messaging simultaneously.

Retail managers at high-traffic stores — pharmacies, specialty shops, airport concessions — reach for this format when a single-sided panel would mean half the shoppers see the back of the hardware instead of a graphic. Two-sided printing solves that problem without floor-plan surgery.

Event agencies and brand activation teams handling multi-day shows also gravitate toward this unit because one bag per stand simplifies load-in logistics significantly. If your team is coordinating a conference with multiple session rooms, consolidating to a two sided banner stand cuts the number of cases rolling through a hotel corridor in half.

What the 33.5 x 80 Fabric Double Sided Retractable Banner Stand Includes

A few features worth highlighting before you finalize artwork:

• Fabric, not film. The dye-sublimation process saturates the polyester fibers rather than coating the surface, so colors stay vivid after repeated rolling and unrolling without cracking or peeling.
• Independent artwork on each face. Both sides accept completely different graphics, so this is not a mirrored or reversed duplicate — you get two distinct ad surfaces.
• Retractable cassette system. The graphic rolls into the base housing for storage and transport, protecting the print between events.
• Lightweight aluminum base. The Silverwing hardware is built for frequent travel: sturdy enough for daily use, light enough to carry alongside other booth materials without blowing the weight budget.
• Complete package. Pole, base, dual graphic, and carry bag are all included — no separate assembly kits or add-on purchases needed.

If you are comparing the silverwing banner stand to a basic economy model, note that the Silverwing mechanism is rated for significantly more use cycles and the tensioning system produces a flatter, more wrinkle-resistant display surface than entry-level cassettes.

Setting Up, Caring For, and Reusing This Display

The setup sequence is deliberate and repeatable. Slide the pole sections together, insert the bottom into the base socket, attach the top bar to the graphic’s leading edge, and retract the release lever to let tension do the rest. The whole process runs about 90 seconds once you have done it once.

For care between events, always roll the graphic into the base before transporting — do not fold or stuff the fabric into a bag separately. If wrinkles appear after extended storage, a handheld garment steamer on a low setting removes them in minutes without damaging the print. Avoid direct heat sources and prolonged direct sunlight, both of which can shift dye-sublimated color over time.

Because the graphic attaches via a top clamp bar rather than adhesive, replacing it later is straightforward. If your messaging changes next quarter, you can order a fresh fabric graphic for the same base without replacing any hardware — a meaningful cost advantage over disposable single-use displays. That reusability is one of the strongest arguments for choosing a retractable banner 33×79 or 80-inch-height format over a rigid panel that ships in a hard case.

Before you go to print, confirm that your artwork files are set up at the correct bleed dimensions and in RGB color mode for dye-sublimation output. Contact the Showfire team if you need a print-ready template for either face.

Comparing This to Other Configurations in the Range

If you want a single-sided version of this same footprint, the 33×80 retractable banner stand in single-sided fabric is available in the broader retractable banner stands catalog. For teams that need a lower price point and are comfortable with a thinner mechanism, the econo roll banner stand offers a budget-friendly single-sided alternative at a similar width. And if you are outfitting a larger exhibit space with multiple units, the trade show pull up banner options include formats that scale well across a long backwall.

For a deeper breakdown of materials, sizing logic, and how double-sided units compare to paired single-sided displays, the retractable banner stand buying guide covers all of it in plain language.

The full range of double sided retractable banner stand configurations — including different heights and graphic material options — lives in the Silverwing collection, where you can compare every available package side by side.

Order This Display and Put Both Sides to Work

The 33.5 x 80 fabric double sided retractable banner stand ships as a complete, ready-to-display package with no hidden add-ons. Place your order today and put two full graphic surfaces on the floor at your next event.